Elenco PK101 w/ Computer Interface Manual de usuario

CI-22BASIC ELECTRONIC EXPERIMENTSwith computer interfaceExperiments PC1-PC8Instruction ManualElenco Electronics, Inc.Copyright © 2003 by Elenco Electr

Now its time to look at your electronic signal in a different way. The oscilloscope features you havebeen using show you voltage (amplitude) vs time,

Set the variable resistor control to mid-range. In addition to the 5ms/div and 0.5ms/div settings forthe horizontal scale, there is also a variable se

Now you can click on the FFT box to return to oscilloscope mode and look at the waveform with the0.1µF capacitor in the circuit. You can observe it wi

Project PC2OBJECTIVE: To see what your voice looks like in electrical form.Speaker MicrophoneA speaker uses electrical energy to create mechanical vib

Smooth, well-rounded, and repetitive waveforms (in oscilloscope mode) have nearly all of their ener-gy at a specific frequency. “Square” or “rectangul

Build the circuit shown. If continuing from the previous experiment then close the Winscope programand run it again, to reset the settings. Click on t

Now change to FFT mode to look at the frequency spectrum as the sound fades away. Try the settingsshown here.The spectrum at left is for justafter pre

Build the circuit shown. If continuing from the previous experiment then close the Winscope programand run it again, to reset the settings. Click on t

+9VSP33kΩ473470Ω502Project PC5OBJECTIVE: To demonstrate storage mode.Electronic Noisemaker PCBuild the circuit shown, connecting the battery last sinc

Winscope has a mode that can display multiple scans at the same time, called Storage mode. Turn thevariable resistor knob to the right, change the Win

Looking at Electronic Signals using the WINSCOPE Software:Electronics engineers use specialized test equipment to “see” electronic signals and make pe

Now turn off storage mode and turn on FFT mode to look at the frequency spectrum, try the settingsshown here. Moving the variable resistor knob will c

+9V100kΩ1kΩ3.3kΩ470ΩSP473502Project PC6OBJECTIVE: To demonstrate wait mode with multiple colors.Noisy Blinker PCBuild the circuit shown. If continuing

Place Winscope in Wait mode by clicking on the button for it, hold down the pushbutton switch, andthen slowly press the On-Line button several times.

Now turn off storage mode and turn on FFT mode to look at the frequency spectrum, try the settingsshown here. Wait mode does not apply in FFT mode, so

Build the circuit and connect the Winscope PC-interface cable as shown. There are 4 resistors and 4capacitors connected to the 3.3kΩ resistor (we are

Build the circuit shown. If continuing from the previous experiment then close the Winscope programand run it again, to reset the settings. Click on t

The waveform will be easier to view if you adjust the horizontal delay, as shown. Using Wait mode alsohelps (press the On-Line button to trigger).You

Elenco Electronics, Inc.150 W. Carpenter AvenueWheeling, IL 60090(847) 541-3800http://www.elenco.come-mail: [email protected]

If you get the picture on the right then your microphone input is not properly turned on, go to the“Turning On Your Microphone Input” to turn it on. T

IMPORTANT NOTE: The designs for the microphone input port vary throughout the computerindustry. Hence you may get waveforms different from those shown

And this waveformmight looklike this.Contact Elenco Electronics if you have any questions about this.Limitations of Winscope and its interface:By usin

Using Winscope’s full capabilities:Winscope has 2 input channels that can be displayed at the same time. This is commonly done byelectronic engineers

SPEAKER+9VSP10kΩ3.3kΩ473-7-Project # Description Page #PC1 Pitch 7PC2 Speaker Microphone 13PC3 Siren PC 15PC4 Space Gun PC 16Project # Description Pag

Click on the On-Line button if Winscope is currently in Hold mode and you should get a picture simi-lar to this one:The waveform peak is off the top o

Move the variable resistor knob and watch how it changes the waveform on the computer screen.Now click on the 0.5ms/div button to change the time scal